Loading... Please wait...

Add to Wish List

Click the button below to add the no case KK2.1.5 Control Board 1.17 lite for full size Tri and mini V and full size V to your wish list.

You Recently Viewed...

Our Newsletter


no case KK2.1.5 Control Board 1.17 lite for full size Tri and mini V and full size V

  • Image 1
Price:
$19.99
Weight:
0.30 LBS
Rating:
Shipping:
Calculated at checkout
Quantity:


Product Description

This board does not come with the case.

 

Latest generation KK2.15 board with updated sensors, memory, header pins, and hard case protection. Also comes with kk2 to receiver wires.
The KK2 is next big evolution of the first generation KK flight control boards. The KK2 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.
The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.
Specifications: Size: 50.5mm x 50.5mm x 12mm Weight: 21 gram (Include Piezo buzzer) IC: Atmega644 PA Gyro/Acc: 6050MPU InvenSense Inc. Auto-level: Yes Input Voltage: 4.8-6.0V AVR interface: standard 6 pin. Signal from Receiver: 1520us (5 channels) Signal to ESC: 1520us Firmware Version: Stevis 1.17 lite  (My Faverite Flash)
Pre-installed firmware. Dualcopter Tricopter Y6 Quadcopter + Quadcopter X Hexcopter + Hexcopter X Octocopter + Octocopter X X8 + X8 X H8 H6 V8 V6 Aero 1S Aileron Aero 2S Aileron Flying Wing Singlecopter 2M 2S Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option) The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.
What is a Multi-Rotor Control board you ask? The KK2 Multi-Rotor controller is a flight control board for multi-rotor aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the 6050MPU gyro/acc (roll, pitch and yaw) then passes the signal to the Atmega644PA IC. The Atmega644PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft. The KK2 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega644PA IC via the aileron, elevator, throttle and rudder inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).


Find Similar Products by Category


Write your own product review

Product Reviews

  1. very good display 4 Star Review

    Posted by on 16th Feb 2017

    easy to setup when you are a beginner